English
français
Deutsch
русский
español
português
Nederlands
العربية
日本語
한국의
ST6 Solar steel Ground Mounting
ST6 Solar steel Ground Mounting is usually applicable to the open filed and ground. It has good strength and can be easy to install for solar panel mounting.
Pile Ground Mounting is one of strong structure of UISOLAR. Steel post can easily dig into the earth around 1.4 meter by machine. The Single Ground mounting have highly corrosion resistant as the hot-dip galvanizing average layer thickness is more than 80μm.
Brand:
UISOLARItem NO.:
UI-ST2Color:
SilverShipping Port:
Xiamen ChinaLead Time：
20 daysInstallation site:
Open fieldMax. wind speed:
80M/SSnow load:
1.4KN/M^2Foundation type:
Pile and ground screwMaterial:
Aluminum 6005-T5&SUS304Standards:
AS/NZS1170,JISC8955:2017
|
Installation Site |
Open field / Ground |
|
Tilt Angel |
0-45 deg |
|
Max wind speed load |
60m/s |
|
Snow Load |
1.4kn/m^2 |
|
Height |
Customized |
|
Foundation |
Pile |
|
Material |
Aluminum 6005-T5 & Hot-dipped galvanized Steel Q235B & Stainless steel 304 |
1. Steel Pile ground mounting structure can suit the open mountainous irregular field, and solve the East-west and South-north directions.
2. High corrosion resistance - aluminum components and stainless parts for the structure.
3. Single post make the maintenance more convenient.
ST6 Solar steel Ground Mounting is usually applicable to the open filed and ground. It has good strength and can be easy to install for solar panel mounting.
UI SOLAR ground ground solar mount usually applicaple to the open field ,not only for residential project ,but also for the big commerial project.
Ground Mounting 90deg Vertical ground The Ground mounting have highly corrosion resitant as the hot dip galvaning average layyer thickness is more than 80um. 1. It can applied to concrte block and piling foundation. 2. Easy to clean solar panels 3. The structure is simple and the bracket is fixed by bolts and pressure blocks.
The Ground Bolt can also accept customized as request. The regular diameter is 76mm, and the Ground Plate diameter can be 200mm and 220mm. The length can be 1.2m, 1.6m, 1.8m and 2m. The thickness is 2.5mm, 2.75mm, 3.0mm. Hot dip galvanized average thickness is more than 80μm.
1. Remove stagnant water automatically 2. Increase power generation to prove the service life of solar panels. 3. Easy installation. Fasten the frame of the solar panel automatically. Suitable for frame thick of solar module: 30 mm, 35 mm, 40 mm 4. Solar Panel Cleaning Clip is a rectangular self-stick polymer strip containing a water-inducing agent. stick to the frame of the photovoltaic module, there is no need to make adjustments to the components. In case of rain, the sludge water collected at the bottom of the frame is automatically directed over the frame and discharged and discharged in the stage of sludge water formation! 5. Through tests, it was found that the water accumulation and dust accumulation along the boundary of the components of the sludge belt was essentially eliminated after the installation of the water guide adhesive, the power generation gain increased from 2% to 10%. 6. Stainless steel material, long service life, no need for frequent replacement.
The new type roof mounting system can fit well on standing seam metal roof sheet and is a very economical solution.
1. Highly pre-assembing make the installation to be easy and quick 2. Al 6005T5 and SUS304 fastener bols are used to get a better anti rusted. 3. Can be flexible for any thickness of panels, no need to change diffent panel clamp.
The solar rooftop mount system suits for metal trapezoidal roof which using hook and screws as rail to save cost.
UISOLAR ABS solar mounting corner bracket is an ideal solution for cable entry through roofs in solar projects. It allows an easy way for cable enter into any roofs under ABS plastic corner. It can be waterproof ,too With its single or dual cable entry, this corner bracket easily passes through solar cables for a smooth installation on any roof surface. In this way, it has wide application in RV,vehicles, caravans, boats, vessel, outbuildings etc.
Nuts are usually matched with bolts. Material: Aluminum 6005-T5, SUS304 and Carbon steel
Solar flashing is a component used in the installation of solar panels on rooftops. It is designed to protect the roof and the solar panel system from water infiltration while ensuring a secure and weathertight seal. It plays a critical role in protecting the building and the solar system from water damage, ensuring the longevity and effectiveness of the solar energy system.
UISOLAR steel ballast mounting is suitable for flat concrete roof, it's made of steel with galvanized zinc surface, anti-corrosion, and without penetrating the roof surface.
Universe Solar(UISOLAR) is a high-tech enterprise specializing in the development,manufacturing and marketing of PV mounting. With our top quality and service, UISOLAR mountings are welcomed by most of the installers, distributors, and EPC ect. all over the world.
Please read on, stay posted, subscribe, and we welcome you to tell us what you think.
online service
+86 (0592)5663849
sales@uisolar.com
solar-mount.au
IPv6 network supported